S&S CYCLE PISTONS 3.625HC SHVL STD- 106-5535

Fits 88in., 93in., 96in., 98in. and 103in. Engines. FORGED PISTONS 3 5/8in. BORE, 88in. ( 7.6:1 C.R.), 93in. (9.3:1 C.R.), 93in. HC (10.1:1 C.R.), 98in. (9.7:1 C.R.), MOTORS AND SIDEWINDER KITS. Replacement pistons available for stock 74in., 80in. and 3 5/8in. big-bore applications. All pistons kits come with two pistons, rings, wrist pins, and wrist pin keepers. Compression ratios listed are approximate and are calculated using the correct length cylinders as specified by S&S. Requires the use of connecting rods with a rod length of 7.440in.(standard length Factory #24281-74A connecting rods); use of earlier connecting rods with a rod length of 7.470in. (Factory #24281-41A) will result in a slight increase in the compression ratio of about 1/2 point, and may also result in clearance problems (check all piston to cylinder head clearances carefully when using the early style rods).1936-1937 fits H-D E 1941-1950 fits H-D E 1936-1952 fits H-D EL 1941-1950 fits H-D F 1941-1964 fits H-D FL 1953-1964 fits H-D FLF 1965-1969 fits H-D FLFB Electra Glide 1958-1964 fits H-D FLH Duo-Glide 1970-1984 fits H-D FLH Electra Glide 1955-1957 fits H-D FLH Hydra-Glide 1965-1969 fits H-D FLHB Electra Glide 1979-1981 fits H-D FLHC Electra Glide Classic 1955-1964 fits H-D FLHF 1970-1972 fits H-D FLHF 1965-1969 fits H-D FLHFB Electra Glide 1980-1981 fits H-D FLHS Electra Glide Sport 1984 fits H-D FLHS Electra Glide Sport 1983 fits H-D FLHTC Electra Glide Classic 1984 fits H-D FLHX Electra Glide Special 1980-1983 fits H-D FLT Tour Glide 1981-1983 fits H-D FLTC Tour Glide Classic 1971-1978 fits H-D FX Super Glide 1980-1982 fits H-D FXB Sturgis 1983 fits H-D FXDG Disc Glide 1974-1984 fits H-D FXE Super Glide 1979-1981 fits H-D FXEF Fat Bob 1982-1983 fits H-D FXR Super Glide II 1982-1983 fits H-D FXRS Low Glide 1983 fits H-D FXRT Sport Glide 1977-1982 fits H

• Replacement pistons available for stock 74in., 80in. and 3 5/8in. big-bore applications
• All pistons kits come with two pistons, rings, wrist pins, and wrist pin keepers
• Compression ratios listed are approximate and are calculated using the correct length cylinders as specified by S&S
• Requires the use of connecting rods with a rod length of 7.440in.(standard length Factory #24281-74A connecting rods); use of earlier connecting rods with a rod length of 7.470in. (Factory #24281-41A) will result in a slight increase in the compression ratio of about 1/2 point, and may also result in clearance problems (check all piston to cylinder head clearances carefully when using the early style rods)