Industrial Steam Iron Curtain Electric Iron Boiler 110V

<p>Introduction:<br>Precaution:<br>The device operates on 110V voltage.<br>The power outlet used must be properly grounded.<br>Never use electrical equipment with damaged cords, and always replace any damaged wiring. Similarly, if the steam hose is damaged and leaks steam, you may contact us for assistance if needed.<br>Avoid direct contact with the iron's base plate during use, as it reaches extremely high temperatures. The recommended ironing mat may also become hot after prolonged use - exercise caution when handling.<br>The device continuously generates intense and high temperature steam. Always prevent steam from directly contacting the skin during operation.<br>Keep children away from the device, especially while it is powered on and in use.<br>Always unplug the device when not in use. Leaving it connected to a power outlet unattended may pose safety hazards, especially for children.<br>Exercise caution when moving the device. Improper handling may cause damage to the equipment.<br>Do not immerse the device in water or any other liquid.<br>Never open the water tank cover while the device is operating.<br>After adding water, do not overtighten the tank cover. If the cover becomes damaged due to excessive tightening, please replace it with a new one.<br>Always unplug the device from the power outlet before performing any water refilling or draining operations on the tank.<br>If the water in the tank runs out during ironing (indicated by the boiler power light turning off) but you need to continue ironing: First, turn off the power.‌ Do not open the water tank cover immediately, as residual steam may still be present. Slowly open the cover until steam begins to escape, then pause and wait for all remaining steam to dissipate completely. Once the steam is fully released, open the cover and refill the tank with an adequate amount of water.<br>Warning:‌ In this process, hot water may splash out due to the remaining heat in the steam boiler. ‌Proceed with caution.‌<br>DO NOT TRY TO REPAIR YOUR DEVICE BY YOURSELF IN CASE OF MALFUNCTION !!! DO NOT OPEN THE INSIDE !!!<br>Operation Method:<br>The scaled water level tube available in your box should be placed vertically into the water inlet hole, with the scaled side of tube down and the water tube touching the bottom of tank. Remove the tube by clogging the top hole with your finger. You will see that there is enough water in the level tube to show the amount of water in the tank. Make sure that the level of water in the tube does not exceed the level of 2 liter. If the level is above 2 liter, please drain excess water.<br>Make sure that the buttons on the front panel of the device are in the off position. Connect the power plug into a grounded electrical outlet nearest to you.<br>STEAM IRONING: Set the two buttons on the front panel to the on position. Set the thermostat knob to a temperature suitable for the fabrc you are ironing. For the device to be ready for ironing: wait for the indicator lamp on the front panel to light up. During this standby, place the wire holding fork in its position. Route the iron cable through the hole in the top of the wire holding fork.<br>When the indicator lamp lights up, it means that your device is ready to iron.<br>Please note: After purchase, we will provide you with a user manual (including warnings and tips) to ensure quick mastery of core functions. Please read the instructions carefully.<br><br>Parameters:<br>Voltage: 110V<br>Frequency: 50-60HZ<br>Water Capacity: 2L(0.5 US Gal)<br>Boiler Input: 1600W<br>Iron Input: 900W<br>Rated Pressure: 0.35MPA<br>Safety Relief Pressure: 0.75MPA<br>Maximum Temperature of Iron: 240˚C<br>Net Weight: 8.6KG(18.9LBS)<br><br>Items Included: 033425-EnzY<br>Industrial Steam Iron Curtain Electric Iron Boiler 110V</p>

• The device comes with a steam boiler system, the water tank is 2L, and the iron is attached to it. Pressurized steam that the resistance creates by boiling the water in the boiler exists; it moves by pressing the control button on the iron, allows perfect ironing from the heat-resistant hose, then flows through the hot channels in the iron and is discharged from the holes of the iron base.
• As long as the steam control knob is pressed, the water in the boiler is constantly steamed at the appropriate pressure.
• Multiple-stage safety system is adopted.
• The boiler input is 1600 Watt, and the iron input is 900 watts per unit. Provides constantly pressurized and dry steam, allowing you to iron quickly and therefore it consumes less energy.
• The device works with 110V electric energy.